Moog CamEvator SERIES Betriebsanleitung

www.videolarm.comC a m E va t o r ™Easily Service Camera at 80 feetInstallation and Operation Instructions for the following models:CV280 Lowering ar

STEP 6:USE A STANDARD LEVEL TO ENSURE THEHORIZONTAL ALINGMENT OF THE UNIT.IF NECESSARY, PLACE WASHERS OR SHIMSBETWEEN LOWERING UNIT AND ADAPTER BRACKE

Detach side plate to access RJ45 extension. Route RJ45 cable for controller through conduit hole, located underneath CamEvator, to the internal RJ4

Wiring Connections Remove the electrical protective cover by removing the four screws. Be sure to replace once the connections are made.• Quite la

Once cables have been attached to camera or surge suppression, place excess wire into provide wire management hook. This will prevent cables from bec

Wrap Teflon tape around the pipe threads to ensure a tight seal. • La cinta del Teflon del abrigo alrededor de la pipa rosca para asegurar un sello

Odd TerminalsEven TerminalsUnprotected Pair 2Unprotected Pair 1Field SideElectronics SideProtected Pair 2Protected Pair 12.125”2.4’Keying PinGround Te

Unprotected or Field Side Connect the RED wire and GREEN wire to the “LINE” of the surge protector. Connect the dome and camera power to the “EQUIP”

PA40 Lowering ArmReplacement Parts List12231918212517813161792028346275210221114152630293334352437364039CamEvatorD Models Only

PA40 Lowering ArmReplacement Parts ListPART # DESCRIPTION1 RPVL3422 LOCKING MECHANISM ASSEMBLY2RPSPPA403EDCO COMM PROTECTOR3RPSPA401EDCO COMM SOCKET4

C a m E v a t o r ™ L o w e r i n g A r m (Moog Videolarm; 1.800.554.1124)Important Note: Please read this addendum and the Installation and Ope

IMPORTANT SAFEGUARDS SAFETY PRECAUTIONSUNPACKINGSERVICE1 Read these instructions.2 Keep these instructions. 3 Heed all warnings 4 Follow

INDEX: (for Addendum) CamEvator Lowering Arm General Operating Description Owner/Employer Responsibilities Safety Procedures Operating Guidelines

CamEvator Lowering Arm General Description:The CamEvator Lowering arm is a device for improving the installation and servicing of overhead cameras and

Owner/Employer Responsibilities:Safety Procedures: Ensure that all Lowering Arm operators are qualied and that they are trained in the safe use and

Operating Guidelines:IMPORTANT OPERATING NOTE: Operator control input is through the Operator Control/Interface Box.The operator must have a key t

Troubleshooting:Error Codes Listed on Operator Interface Control Unit:There are (9) switches that perform various functions in the system. They are:

Preventive Maintenance Schedule:- END -Ground Level: During Each Servicing of the Camera, or raising/lowering of the payload: - Ensure that all

Product Registration/WarrantyThank you for choosing Moog Videolarm. We value your patronage and are solely committed to providing you with the highes

Limited Warranty for Moog Videolarm Products Moog Videolarm warrants these products to be free from defects in material or workmanship as follows:PROD

CamEvatorPower 120 VAC 10 A MaxMaximum weight limit of 35 lbs (15.9kg) may be attached to lowering device.CamEvator may be lowered to a maximum

FrançaisDeutschItalianoPortugueseEspañol!!Operation SpecificationsFrançaisDeutschItalianoPortugueseEspañolEnglishSTEP 6:USE A STANDARD LEVEL TO ENSURE

Warning Labels- NEVER OBSCURE THE WARNING INSTRUCTION LABELS.Etiquetas amonestadoras- NUNCA OBSCUREZCA LAS ETIQUETAS DE INSTRUCCIÓN AMONESTADORAS.Étiq

- PREVENT KINKS BEFORE THEY OCCUR.!!a. This is the start of a kink. At this time, the wire rope should be straightened.b. The wire rope was pulled a

!!Torções do fio- IMPEÇA TORÇÕES ANTES QUE OCORRAM. a. Este é o começo de uma torção. Neste tempo, a corda de fio deve ser endireitada.b. A corda de f

Odd TerminalsUnprotected or Field Side Attach sway plate with the appropriate hardware as shown.• Ate la placa del sacudimiento con el hardware apro